REGISTER YOUR SYSTEM WARRANTY (220V H.E. CONDENSER)

Split System Checklist - 220V Cassette Condensers

1. Owner Information

Owner First Name:

Owner Email:

Owner Last Name:

Owner Phone Number:

Date of Purchase:

Owner Address

Address Line 1:

Address Line 2:

City:

State:

Zip Code:

Country:

2. System Information

System Model:

Fan Coil Serial Number:

Condensing Unit Model Number:

Condensing Unit Serial Number:

3. Installer Information

Company Name:

License Number:

Date of Startup:

Company Address

Address Line 1:

Address Line 2:

City:

State:

Zip Code:

Country:

Technician Name:

Technician Email:

Technician Phone Number:

Certification ID Number:

Certification Source (e.g. NATE):

4. Wine Cellar Information

Room Dimensions

Height:

Length:

Width:

Insulation R-values

Interior Walls:

Exterior Walls:

Ceiling:

Vapor Barrier:

Yes

Glass windows and/or stone/concrete walls?

Yes

Details:

5. DATA RECORDINGS

Note: All readings need to be taken while the compressor is running. Ensure all grilles, filters, components, and ducting (if applicable), are properly installed before recording data. Also, allow a minimum of 30 minutes of run time to ensure system is properly stabilized.

Airflow in and out of the condenser is clear of obstructions. Condensing unit supply and return must have a minimum of three feet of clearance.

Yes

Airflow in and out of the evaporator is clear of obstructions. Evaporator unit supply and return must have a minimum of three feet of clearance.

Yes

a. Line set length:

b. Suction line installed tubing diameter OD:

c. Liquid line installed tubing diameter OD:

d. Bottle probe has been connected to the evaporator unit and inserted into a wine bottle that is 3/4 full? If no, place the bottle probe in a warm bottle of water to ensure the compressor is running throughout the duration of the data recording.

Yes

e. Are there any visible bubbles in the sight glass with the system running? If yes, add refrigerant to clear the sight glass. Ensure that the system is fully charged before taking data recordings.

Yes

f. Temperature of air entering the evaporator coil (dry bulb):

Temperature of air entering the evaporator cooling unit, commonly known as "Return Air". Using a calibrated thermometer, place the sensor in the center of the coil, or return grille 1 inch from touching any surface.

g. Temp of supply air leaving unit (dry bulb):

Temperature of air leaving the evaporator cooling unit, commonly known as "Supply Air". Using a calibrated thermometer, place the sensor in the center of the air flow, 1 inch from touching any surface. Using a calibrated thermometer, place the sensor in the center of the coil, or return grille 1 inch from touching any surface.

h. Temperature difference between return and supply air (f - g):

The temperature difference between return air temperature and supply air temperature of the evaporator cooling unit is commonly known as "Delta". Equation: Return Air subtracted from Supply Air. (a-b = Delta T) Using a calibrated thermometer, place the sensor in the center of the coil, or return grille 1 inch from touching any surface.

i. If the outside air temp is lower than 60°F, a portion of the coil will need to be blocked to stabilize the condensing temp. at 130° psig. Is the coil blocked to raise the condensing temp?

Yes

j. Temp. of air entering the condensing unit:

The temperature of air entering the coil of the condensing unit is commonly known as "Ambient Air". Using a calibrated thermometer, place the sensor in the center of the condensing unit coil, 1 inch from touching any surface. Using a calibrated thermometer, place the sensor in the center of the coil, or return grille 1 inch from touching any surface.

k. Head pressure PSIG at the liquid line king valve:

This pressure reading is taken at the high side of the condensing unit and will range from 100-200 Psi. This pressure is commonly known as "High Side Pressure". Using a calibrated manifold, this pressure is taken at the liquid line service valve.

l. Head pressure which is converted to temperature:

This reading is pressure converted to temperature. This reading is provided from the R134a Pressure Temperature Conversion Chart. Example: 216.3 Psi =136˚FThis pressure is commonly known as "High Side Pressure". Using a calibrated manifold, this pressure is taken at the liquid line service valve.

m. Temperature of liquid line at the liquid line king valve:

This measurement is the actual temperature of the copper line at the liquid line king valve. Using a calibrated thermometer tightly secure the sensor with electrical tape to ensure solid contact to the surface of the copper line. Insulate the sensor to ensure there is no temperature influence from the condenser exhaust air. This will ensure you are reading the correct copper line temperature and not the surrounding air temperature.

n. Sub-cooling calculation (between 5°-15° degrees) (l - m):

The subcooling calculation is the head pressure converted to temperature subtracted from the liquid line temperature. Equation - head pressure converted to temperature subtracted from the liquid line temperature. (f-g = h) WhisperKOOL cooling units achieve optimum performance with a 5˚F subcooling at an ambient of 85˚F.

o. Suction pressure PSIG at the suction service valve:

This is the pressure reading taken at the low side of the condensing unit and will range from 24-50 Psi. This pressure reading is commonly known as "Low Side Pressure". Using a calibrated manifold, this pressure is taken at the Suction service valve.

p. Suction pressure converted to temperature:

This reading is pressure converted to temperature. This reading is provided from the R134a PT Conversion Chart. Example: 30.4 Psi = 35˚F

q. Temperature of suction line at the service valve:

This measurement is the actual temperature of the copper line at the suction line service valve.

r. Superheat calculation (between 10°-25°)(q - p):

The superheat calculation is the temperature of the suction line subtracted from the suction pressure converted to temperature. Equation - the temperature of the suction line subtracted from the suction pressure converted to temperature. (k-j = l)

s. Voltage to compressor (running):

Voltage is taken with a calibrated volt meter. Measure the voltage going from the connections going into the condensing unit for power. The system is rated for 120V (Unless stated 220 on condensing unit). Voltage must be between 113-130 Volts.

t. Amp. draw at the time of data recording (running):

Using a calibrated amp meter, clamp the meter onto the "hot wire". This will be the black wire in the electrical box. Amps must not exceed manufacturing rating on the name plate.

u. Was a condensation drain test performed?

Yes

If no, pour water into the drain pan to verify that the unit is draining properly.

Image Upload

Choose File

Disclaimer:

Split System Warranty: A limited 2-year product warranty is offered with all split systems. While the warranty starts at the date of purchase, this warranty is not activated until a Product Warranty Checklist has been submitted and approved by WhisperKOOL.

I have read and agree to the Terms and Conditions and Privacy Policy